Need Help with my code.

Welcome Forums General PowerShell Q&A Need Help with my code.

This topic contains 2 replies, has 2 voices, and was last updated by

 
Participant
3 years, 7 months ago.

  • Author
    Posts
  • #28151

    Participant
    Points: 4
    Rank: Member

    Dear Community

    I need your help with my below code.
    I have a list of servers that I need to check 4 services and output result .
    If the service is running it will return "ok" as a result. This works but I have a problem
    capturing the error if the service fails.

    I am getting below error message
    Get-HypServiceStatus : Cannot bind parameter 'ErrorAction'. Cannot convert value "hypervisor" to type "System.Management.Automation.ActionPreference". Error: "Unable to match the
    identifier name hypervisor to a valid enumerator name. Specify one of the following enumerator names and try again: SilentlyContinue, Stop, Continue, Inquire, Ignore, Suspend"
    At C:\Temp\Svrsitecheck.ps1:36 char:78
    + $Hypervisor = Get-HypServiceStatus -AdminAddress $Controller -ErrorAction hyp
    .

    The result should be something like this.
    ControllerName : Controller1.exmaple.com
    BrokerService : service is up and running
    ConfigService : service is up and running on
    HypervisorService : service is up and running on
    ADIdentityService : service is up and running on

    Thanks

    $controllers = Get-content C:\controllers.txt 
    foreach ($Controller in $Controllers)
    { 
       $broker = Get-BrokerServiceStatus -AdminAddress $Controller -ErrorVariable broker
        if ($broker -eq 'ok')
       { 
          $broker = "service is up and running" }
       
       else {
       $broker = "Service is not running on "}
    
       $config = Get-ConfigServiceStatus -AdminAddress $Controller -ErrorVariable config
       if ($config -eq 'ok')
       { 
       
       $config = "service is up and running on " }
       
       else {
    
       $config = "Service is not running on "}
    
       $Hypervisor = Get-HypServiceStatus -AdminAddress $Controller -ErrorAction hypervisor
       if ($Hypervisor -eq 'ok')
       { 
       
       $Hypervisor = "service is up and running on " }
       
       else {
       $Hypervisor = "Service is not running on"}
    
       $ADAccount = Get-AcctServiceStatus -AdminAddress $Controller -ErrorAction ADAccount
       if ($ADAccount -eq 'ok')
       { 
       
       $ADAccount = "service is up and running on " }
       
       else {
       $ADAccount = "Service is not running on "}
       $status+= New-Object psobject -Property @{ControllerName = $Controller 
                                                 BrokerService = $broker
                                                 ConfigService = $config
                                                 HypervisorService = $Hypervisor
                                                 ADIdentityService = $ADAccount
                                                 }}
        $status | Select-Object ControllerName,BrokerService,ConfigService,HypervisorService,ADIdentityService
    
    
    
    
  • #28152

    Participant
    Points: 0
    Rank: Member

    I think the first place to start is the following line:

    $Hypervisor = Get-HypServiceStatus -AdminAddress $Controller -ErrorAction hypervisor

    If you notice, part of the error gives you a clue as to what's wrong:

    Error: "Unable to match theidentifier name hypervisor to a valid enumerator name. Specify one of the following enumerator names and try again: SilentlyContinue, Stop, Continue, Inquire, Ignore, Suspend"

    When you specify the -ErrorAction parameter, the value must be one of a given set (SilentlyContinue, Stop, Continue, Inquire, Ignore, Suspend), and you are assigning the parameter the value "hypervisor" which is not part of the set.

  • #28155

    Participant
    Points: 4
    Rank: Member

    My bad 🙂 .. Thanks Vaskan . I was intend to use errorvariable but i end up typing erroraction and did not look in to it. 🙂 i should have strong coffee now.. 🙂 its working fine now.. thanks again for your timely response

The topic ‘Need Help with my code.’ is closed to new replies.

denizli escort samsun escort muğla escort ataşehir escort kuşadası escort