Script to validate credentials then start a program

Welcome Forums General PowerShell Q&A Script to validate credentials then start a program

Viewing 1 reply thread
  • Author
    Posts
    • #211038
      Participant
      Topics: 2
      Replies: 1
      Points: 18
      Rank: Member

      Hello, I am trying to run a script to validate users credentials via a.d and then once validated it proceeds to run a program. At the moment, the credentials are being validated but the credentials are not being passed to run the program. The program launches with my userid rather than the entered domain user credentials.

       

      [CmdletBinding()]
      
      Param (
      
      [Parameter(Mandatory = $False)]
      
      [Int]$MaxAttempts = 5
      
      )
      
      Add-Type -AssemblyName System.DirectoryServices.AccountManagement
      
      $UserDomain = $env:USERDOMAIN
      
      $UserName = "$UserDomain\$env:USERNAME"
      
      $Attempt = 1
      
      $CredentialPrompt = "Enter your domain credentials:"
      
      $ValidAccount = $False
      
      # Loop through prompting for and validating credentials, until the credentials are confirmed, or the maximum number of attempts is reached.
      
      Do {
      
      # Blank any previous failure messages and then prompt for credentials with the custom message and the pre-populated domain\user name.
      
      $FailureMessage = $Null
      
      $Credentials = Get-Credential -UserName $UserName -Message $CredentialPrompt
      
      # Verify the credentials prompt wasn't bypassed.
      
      If ($Credentials) {
      
      # If the user name was changed, then switch to using it for this and future credential prompt validations.
      
      If ($Credentials.UserName -ne $UserName) {
      
      $UserName = $Credentials.UserName
      
      }
      
      # Test the user name (even if it was changed in the credential prompt) and password.
      
      $ContextType = [System.DirectoryServices.AccountManagement.ContextType]::Domain
      
      Try {
      
      $PrincipalContext = New-Object System.DirectoryServices.AccountManagement.PrincipalContext $ContextType,$UserDomain
      
      } Catch {
      
      If ($_.Exception.InnerException -like "*The server could not be contacted*") {
      
      $FailureMessage = "Could not contact a server for the specified domain. Please try again after a few minutes."
      
      } Else {
      
      $FailureMessage = "Unpredicted failure: "$($_.Exception.Message)" Please realunch OnBase"
      
      }
      
      }
      
      # If there wasn't a failure talking to the domain test the validation of the credentials, and if it fails record a failure message.
      
      If (-not($FailureMessage)) {
      
      $ValidAccount = $PrincipalContext.ValidateCredentials($UserName,$Credentials.GetNetworkCredential().Password)
      
      If (-not($ValidAccount)) {
      
      $FailureMessage = "Incorrect Credentials #$Attempt out of $MaxAttempts."
      
      }
      
      }
      
      # Otherwise the credential prompt was (most likely accidentally) bypassed so record a failure message.
      
      } Else {
      
      EXIT
      
      }
      
      # If there was a failure message recorded above, display it, and update credential prompt message.
      
      If ($FailureMessage) {
      
      Write-Warning "$FailureMessage"
      
      $Attempt++
      
      If ($Attempt -lt $MaxAttempts) {
      
      $CredentialPrompt = "Invalid Credentials:"
      
      } ElseIf ($Attempt -eq $MaxAttempts) {
      
      $CredentialPrompt = "Invalid Credentials:"
      
      }
      
      }
      
      } Until (($ValidAccount) -or ($Attempt -gt $MaxAttempts))
      
      Write-Host ""
      
      If (-not($ValidAccount)) {
      
      Write-Host -ForegroundColor Red "You failed $MaxAttempts attempts at providing a valid user credentials. "
      
      EXIT
      
      } Else {
      
      Start-Process powershell -Credential -Credentials -ArgumentList '-noprofile -command &{Start-Process -FilePath "C:\Users\Public\Desktop\program" -verb runas}' -WindowStyle Minimized
      
      }
    • #211041
      Participant
      Topics: 0
      Replies: 3
      Points: -4
      Rank: Member

      Your fault is you are not passing the credential using the variable $credential.

      Fix the line starting powershell like this:

      Start-Process “powershell.exe” -Credential $Credentials …..

       

      • #211050
        Participant
        Topics: 2
        Replies: 1
        Points: 18
        Rank: Member

        Hi,

        Thank you for the update. I just tried that, and here is the error message:

        Start-Process : This command cannot be run due to the error: The user name or password is incorrect.
        At C:\Users\myuserid\Documents\Confirm-Credentials.ps1:75 char:2
        + Start-Process “powershell.exe” -Credential $Credentials -Argument …
        + ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
        + CategoryInfo : InvalidOperation: (:) [Start-Process], InvalidOperationException
        + FullyQualifiedErrorId : InvalidOperationException,Microsoft.PowerShell.Commands.StartProcessCommand

        Although, i did enter the right username and password

Viewing 1 reply thread
  • You must be logged in to reply to this topic.